View UPG2160T5K-E2_1106011.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

GaAs INTEGRATED CIRCUIT
PG2160T5K
L, S-BAND SINGLE CONTROL SPDT SWITCH
DESCRIPTION
The PG2160T5K is a GaAs MMIC for L, S-band SPDT (Single Pole Double Throw) switch which was developed for mobile phone and other L, S-band applications. This device can operate frequency from 0.5 to 3.0 GHz, with low insertion loss and high isolation. This device is housed in a 6-pin plastic TSSON (Thin Shrink Small Out-line Non-leaded) package, and is suitable for high-density surface mounting.
FEATURES
* Supply voltage * Switch control voltage * : VDD = 2.4 to 2.8 V (2.6 V TYP.) : Vcont (H) = 2.4 to VDD (2.6 V TYP.) : Vcont (L) = -0.2 to 0.2 V (0 V TYP.) Low insertion loss : Lins1 = 0.30 dB TYP. @ f = 0.5 to 1.0 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V : Lins2 = 0.35 dB TYP. @ f = 1.0 to 2.0 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V : Lins3 = 0.40 dB TYP. @ f = 2.0 to 2.5 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V : Lins4 = 0.50 dB TYP. @ f = 2.5 to 3.0 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V High isolation : ISL1 = 25 dB TYP. @ f = 0.5 to 1.0 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V : ISL2 = 18 dB TYP. @ f = 1.0 to 2.0 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V : ISL3 = 17 dB TYP. @ f = 2.0 to 2.5 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V : ISL4 = 13 dB TYP. @ f = 2.5 to 3.0 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V Handling power : Pin (0.1 dB) = +21.0 dBm TYP. @ f = 2.0/2.5 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V High-density surface mounting : 6-pin plastic TSSON package (1.0 x 1.0 x 0.37 mm)
*
* *
APPLICATIONS
* L, S-band digital cellular or cordless telephone TM * W-LAN, WLL and Bluetooth etc.
ORDERING INFORMATION
Part Number Order Number Package 6-pin plastic TSSON (Pb-Free)
Note
Marking G4
Supplying Form * Embossed tape 8 mm wide * Pin 1, 6 face the perforation side of the tape * Qty 5 kpcs/reel
PG2160T5K-E2
PG2160T5K-E2-A
Note With regards to terminal solder (the solder contains lead) plated products (conventionally plated), contact your nearby sales office. Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: PG2160T5K-A
Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge.
Document No. PG10635EJ01V0DS (1st edition) Date Published September 2006 NS CP(K)
2006
PG2160T5K
PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM
(Top View)
1 6
(Top View)
1 6 6
(Bottom View)
1
Pin No. 1 2 3
Pin Name OUTPUT1 GND OUTPUT2 Vcont INPUT
VDD
G4
Vcont High Low Parameter Parameter
Note
2
5
2
5
5
2
4 5
6
3
4
3
4
4
3
TRUTH TABLE
INPUT-OUTPUT1 OFF ON INPUT-OUTPUT2 ON OFF
ABSOLUTE MAXIMUM RATINGS (TA = +25C, unless otherwise specified)
Symbol VDD Vcont Pin TA Tstg Ratings +6.0 +6.0 +26 -45 to +85 -55 to +135 Unit V V dBm C C
Supply Voltage Switch Control Voltage Input Power Operating Ambient Temperature Storage Temperature
RECOMMENDED OPERATING RANGE (TA = +25C, unless otherwise specified)
Symbol VDD
Note
MIN. 2.4 2.4 -0.2
TYP. 2.6 2.6 0
MAX. 2.8 VDD 0.2
Unit V V V
Supply Voltage
Switch Control Voltage (H) Switch Control Voltage (L)
Vcont (H) Vcont (L)
Note Vcont (H) VDD
2
Data Sheet PG10635EJ01V0DS
PG2160T5K
ELECTRICAL CHARACTERISTICS (TA = +25C, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V, DC cut capacitors = 56 pF, unless otherwise specified)
Parameter Insertion Loss 1 Insertion Loss 2 Insertion Loss 3 Insertion Loss 4 Isolation 1 Isolation 2 Isolation 3 Isolation 4 Input Return Loss Output Return Loss 0.1 dB Loss Compression Input Power
Note
Symbol Lins1 Lins2 Lins3 Lins4 ISL1 ISL2 ISL3 ISL4 RLin RLout Pin (0.1 dB)
Test Conditions f = 0.5 to 1.0 GHz f = 1.0 to 2.0 GHz f = 2.0 to 2.5 GHz f = 2.5 to 3.0 GHz f = 0.5 to 1.0 GHz f = 1.0 to 2.0 GHz f = 2.0 to 2.5 GHz f = 2.5 to 3.0 GHz f = 0.5 to 3.0 GHz f = 0.5 to 3.0 GHz f = 2.0/2.5 GHz
MIN. - - - - 22 15 14 10 15 15 +18.0
TYP. 0.30 0.35 0.40 0.50 25 18 17 13 20 20 +21.0
MAX. 0.45 0.50 0.55 0.65 - - - - - - - - - 100 20 -
Unit dB
dB
dB dB dBm
2nd Harmonics 3rd Harmonics Supply Current Switch Control Current Switch Control Speed
2f0 3f0 IDD Icont tSW
f = 2.0/2.5 GHz, Pin = +10 dBm f = 2.0/2.5 GHz, Pin = +10 dBm No signal
65 65 - -
75 75 50 4 150
dBc dBc
A A
ns
50% CTL to 90/10% RF
-
Note Pin (0.1 dB) is measured the input power level when the insertion loss increases more 0.1 dB than that of linear range. Caution This device is used it is necessary to use DC cut capacitors.
Data Sheet PG10635EJ01V0DS
3
PG2160T5K
EVALUATION CIRCUIT
VDD INPUT Vcont
1 000 pF C0
1 000 pF
6
5
4
1
2
3
C0
C0
OUTPUT1
OUTPUT2
Remark C0 : 56 pF
The application circuits and their parameters are for reference only and are not intended for use in actual design-ins.
4
Data Sheet PG10635EJ01V0DS
PG2160T5K
ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD
Vcont
OUTPUT2
C
5
INPUT
C1
G4
C
4
C
C
3
2
OUTPUT1
VDD
USING THE NEC EVALUATION BOARD
Symbol C1, C2, C3 C4, C5 Values 56 pF 1 000 pF
Data Sheet PG10635EJ01V0DS
5
PG2160T5K
TYPICAL CHARACTERISTICS (TA = +25C, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V, DC cut capacitors = 56 pF, using test fixture, unless otherwise specified)
INPUT-OUTPUT1 INSERTION LOSS vs. FREQUENCY
2.5 2.0
Insertion Loss Lins (dB)
1: 2: 3: 4: 5:
INPUT-OUTPUT2 INSERTION LOSS vs. FREQUENCY
2.5 2.0
Insertion Loss Lins (dB)
1: 2: 3: 4: 5:
-0.255 dB
0.5 GHz -0.305 dB 1.0 GHz -0.355 dB 2.0 GHz -0.408 dB 2.5 GHz -0.502 dB 3.0 GHz
-0.255 dB
0.5 GHz
-0.304 dB
1.0 GHz
1.5 1.0 0.5 0 -0.5 -1.0 -1.5 -2.0 -2.5 0.1 0.7 1.3 1.9
1
1.5 1.0 0.5 0 -0.5 -1.0 -1.5 -2.0
-0.354 dB
2.0 GHz
-0.408 dB
2.5 GHz
-0.506 dB
3.0 GHz
1 2 3 4
2
3
4
5
5
2.5
3.1
-2.5 0.1
0.7
1.3
1.9
2.5
3.1
Frequency f (GHz)
Frequency f (GHz)
INPUT-OUTPUT1 ISOLATION vs. FREQUENCY
50 40 30
Isolation ISL (dB)
1: 2: 3: 4: 5:
INPUT-OUTPUT2 ISOLATION vs. FREQUENCY
50 40 30
Isolation ISL (dB)
1: 2: 3: 4: 5:
-30.53 dB
0.5 GHz -24.659 dB 1.0 GHz -19.114 dB 2.0 GHz -17.362 dB 2.5 GHz -15.87 dB 3.0 GHz
-30.378 dB
0.5 GHz
-24.496 dB
1.0 GHz
-18.545 dB
2.0 GHz
20 10 0 -10 -20 -30 -40 -50 0.1 1 2 3
20 10 0 -10 -20 -30 -40 1 2 3
-17.212 dB
2.5 GHz
-15.717 dB
3.0 GHz
4
5
4
5
0.7
1.3
1.9
2.5
3.1
-50 0.1
0.7
1.3
1.9
2.5
3.1
Frequency f (GHz)
Frequency f (GHz)
INPUT-OUTPUT1 INPUT RETURN LOSS vs. FREQUENCY
50 40
Input Return Loss RLin (dB)
1: 2: 3: 4: 5:
INPUT-OUTPUT2 INPUT RETURN LOSS vs. FREQUENCY
50 40
Input Return Loss RLin (dB)
1: 2: 3: 4: 5:
-18.298 dB
0.5 GHz -22.409 dB 1.0 GHz -28.233 dB 2.0 GHz -31.992 dB 2.5 GHz -27.286 dB 3.0 GHz
-18.557 dB
0.5 GHz
-23.14 dB
1.0 GHz
30 20 10 0 -10 -20 -30 -40 -50 0.1 2 3 1
30 20 10 0 -10 -20 -30 -40 2 3 1
-29.248 dB
2.0 GHz
-28.445 dB
2.5 GHz
-23.756 dB
3.0 GHz
4
5
4
5
0.7
1.3
1.9
2.5
3.1
-50 0.1
0.7
1.3
1.9
2.5
3.1
Frequency f (GHz)
Frequency f (GHz)
Remark The graphs indicate nominal characteristics.
6
Data Sheet PG10635EJ01V0DS
PG2160T5K
INPUT-OUTPUT1 OUTPUT RETURN LOSS vs. FREQUENCY
50
Output Return Loss RLout (dB)
1: 2: 3: 4: 5:
INPUT-OUTPUT2 OUTPUT RETURN LOSS vs. FREQUENCY
50
Output Return Loss RLout (dB)
1: 2: 3: 4: 5:
-18.38 dB
0.5 GHz -22.911 dB 1.0 GHz -28.715 dB 2.0 GHz -30.049 dB 2.5 GHz -25.211 dB 3.0 GHz
-18.646 dB
0.5 GHz
40 30 20 10 0 -10 -20 -30 -40 -50 0.1 0.7 1.3 2 3 1.9 1
40 30 20 10 0 -10 -20 -30 -40 -50 0.1 0.7 1.3 2 3 1.9 1
-23.332 dB
1.0 GHz
-31.078 dB
2.0 GHz
-28.398 dB
2.5 GHz
-23.042 dB
3.0 GHz
4 2.5
5
5 4 2.5 3.1
3.1
Frequency f (GHz)
Frequency f (GHz)
OUTPUT POWER vs. INPUT POWER
+35 f = 2.0 GHz
Output Power Pout (dBm)
+30 +25 +20 +15 +10 +5 +8
+12
+16
+20
+24
+28
Input Power Pin (dBm)
Remark The graphs indicate nominal characteristics.
Data Sheet PG10635EJ01V0DS
7
PG2160T5K
MOUNTING PAD DIMENSIONS 6-PIN PLASTIC TSSON (UNIT: mm)
0.31
0.29
0.29
0.31
Remark The mounting pad layouts in this document are for reference only.
8
6-0.22
Data Sheet PG10635EJ01V0DS
0.35
0.35
PG2160T5K
PACKAGE DIMENSIONS 6-PIN PLASTIC TSSON (UNIT: mm)
(Top View)
1.00.1
1.00.1
(Bottom View)
1.00.1
0.15+0.07 -0.05
0.15+0.07 -0.05
0.350.06 0.350.06
0.45 0.1
1.00.1
0.130.07 0.230.07
0.1750.075
0.37+0.03 -0.05
Data Sheet PG10635EJ01V0DS
9
PG2160T5K
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered and mounted under the following recommended conditions. methods and conditions other than those recommended below, contact your nearby sales office.
Soldering Method Infrared Reflow Soldering Conditions Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220C or higher Preheating time at 120 to 180C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) Wave Soldering Peak temperature (molten solder temperature) Time at peak temperature Maximum number of flow processes Maximum chlorine content of rosin flux (% mass) Partial Heating Peak temperature (terminal temperature) Soldering time (per side of device) Maximum chlorine content of rosin flux (% mass) : 260C or below : 10 seconds or less : 60 seconds or less : 12030 seconds : 3 times : 0.2%(Wt.) or below : 260C or below : 10 seconds or less : 1 time : 0.2%(Wt.) or below : 350C or below : 3 seconds or less : 0.2%(Wt.) or below HS350 WS260 Condition Symbol IR260
For soldering
Preheating temperature (package surface temperature) : 120C or below
Caution Do not use different soldering methods together (except for partial heating).
10
Data Sheet PG10635EJ01V0DS
PG2160T5K
Bluetooth is a trademark owned by Bluetooth SIG, Inc., U.S.A.
* The information in this document is current as of September, 2006. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. * No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document. * NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. * Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. * While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. * NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application. (Note) (1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above).
M8E 02. 11-1
Data Sheet PG10635EJ01V0DS
11
PG2160T5K
Caution
GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. * Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. * Do not burn, destroy, cut, crush, or chemically dissolve the product. * Do not lick the product or in any way allow it to enter the mouth.
For further information, please contact NEC Compound Semiconductor Devices Hong Kong Limited E-mail: contact@ncsd-hk.necel.com Hong Kong Head Office TEL: +852-3107-7303 FAX: +852-3107-7309 Taipei Branch Office TEL: +886-2-8712-0478 FAX: +886-2-2545-3859 Korea Branch Office TEL: +82-2-558-2120 FAX: +82-2-558-5209 NEC Electronics (Europe) GmbH http://www.eu.necel.com/ TEL: +49-211-6503-0 FAX: +49-211-6503-1327 California Eastern Laboratories, Inc. http://www.cel.com/ TEL: +1-408-988-3500 FAX: +1-408-988-0279 Compound Semiconductor Devices Division NEC Electronics Corporation URL: http://www.ncsd.necel.com/
0604
4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix -A indicates that the device is Pb-free. The -AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL's understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information.
Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*)
If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL's liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.

▲Up To Search▲

Price & Availability of UPG2160T5K-E2

	To Download UPG2160T5K-E2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .